GORT

Reviews

Fiat 500 Selespeed Gearbox Self-Calibration

Di: Everly

Hydraulic Unit Automatic Gearbox Selespeed Fiat 500 Panda Punto Lancia ...

– Enable clutch self calibration or calculate degradation index – EOL service Calculate degradation index 1) Put key on MAR, 2) Connect with FES to selespeed ECU, 3)

Hello, I have fiat panda 2006, 1.25cc with SELESPEED CFC228F Automatic Gearbox for the last few days i had a problem with code P0715 – Clutch disk speed, as i

Fiat Abarth 500 Not completing End Of Line Calibration p2917

My mums fiat 500 suddenly stopped working in terms of getting into gear. It comes up with a transmission Forums. New posts Featured threads Search forums Members list

To setup the clutch correctly, adjust manually to 28,00 – 28,50mm (2.0TS / JTS Selespeeds and the most Fiat) and ready! After this you can run the self calibration of clutch

„Clutch self-calibration enable“ – allows the system to „learn“ the new clutch. You need to run the engine up to temperature before starting this one. „Production/service final

For example, to check whether clutch is slipping (for a Selespeed ECU) move „Engine rpm“ and „Clutch disk speed“ meters to the same tab, activate and zoom them, start

  • USING THE SELESPEED GEARBOX
  • Selespeed Clutch self calibration
  • Alfa Romeo TCT Training Manual1

My girlfriend has an Automatic 2011 Fiat 500 0.9 TwinAir. Recently, it keeps jumping into Neutral, and wont shift back into gear without turning it off and on again. I believe

Have you done the software calibrations? In particular the end-of-line calibration (what MES calls a Production/Service final calibration)? Though this should be preceded by

Car wouldnt go into gear, had “unable to select gear” warning. Car has been in garage and had a new tcm fitted. This didnt fix fault, so they have now suggested new clutch.

Selespeed Clutch self calibration

Consider to support my channel and all the hard work put into it at http://www.patreon.com/LMAutoRepairsThank youHiUnfortunately I failed to record the disas

Thought I would give a little update on the dualogic/selespeed thread, I’ve now bought a Grande Punto dualogic with gearbox issues, I’m going to run the car for 6 months or

I am having issues with a Calibration on the software to enable the clutch to calibrate. I am getting and Error code of P290E-55 – Clutch Self Calibration Enable. It says

I found a log for a similar transmission showing I don’t normally have a problem. (Multiecuscan 4.6R1) 18/06/2020 10:58:01 Fiat 500 1.4 Turbo 16V T-Jet/MultiAir Abarth Marelli

My mums fiat 500 suddenly stopped working in terms of getting into gear. It comes up with a transmission error. So we narrowed it down to a leak under the car. So, what I need

  • The one and only Dualogic failure thread
  • how to solve "clutch stroke insufficient"
  • General Fiat 500 Duologic Transmission error selespeed
  • Selespeed/Automatic Gearbox Help
  • Selespeed clutch calibration finishes too quickly

As I could find the ’semi automatic transmission‘ in the Fiat 500 is only an electrohydraulically motorized manual gearbox, FIAT called the system Dualogic. It is the same

I have a 147 selespeed that appears to have a clutch that is out of calibration or worn. Sometimes the clutch will drag when sitting still (i.e. the engine stalls or stalling when

Videos von Fiat 500 selespeed gearbox self-calibration

Engines that will fit a FIRE gearbox? dear everybody, recently, I found my car had difficulty to engage reverse gear, so I take the actuator out & change the oil ,however, the

Fiat 500 automatic gearbox actuator dualogic selespeed repair (When the ...

With the new TCM, did it go through the calibration procedure? If the issue continues, I’d assume that it errored out. The clutch probably isn’t an issue, likely something

Alfa owners seem to have a lot more experience with the system through the selespeed. My Fiat dualogic gearbox doesn’t like changing gears. There’s not a lot in the way

Over this past couple of weeks things have been a lot smoother when changing gears since putting the fresh gearbox oil in, adjusting the clutch rod to 28mm and doing clutch

Hey, i have a 2008 500 with selespeed cfc328, the issue is after removing & reinstalling the gearbox to change the crankshaft seal, the car wont engage 4th gear, RN123

USING THE SELESPEED GEARBOX USING THE SELESPEED GEARBOX The car is fitted with a mechanical gearbox with electronic control, called Selespeed that works in two operating

The only gearbox procedure I can find that includes driving is recalculation of the degredation index. I’ve read somewhere that the cause may be that I’m using an ELM interface

Hi All, I am looking to buy a 500C in Australia. In the local market it is only available with the Dualogic box. The dealers represent it as an „automatic“ so I drove it as such

Given that my Fiat 500 is probably only worth £2.5K now, I decided not to have a complete replacement of the gearbox but now looking for any suggestions on how I can get it

Hi all, Iv just bought a 56 plate grande punto with a dualogic/selespeed issue i cannot select any gear its just stuck in neutral i can hear the pump slightly and the pressure

Fiat 500 selespeed gearbox self-calibration, dear everybody, recently, I found my car had difficulty to engage reverse gear, so I take the actuator out & re-

2- With my Stilo running sweet and back on the road, it was time to revisit another Stilo, this one with Selespeed problems. The pump had not been running and the battery was

Check selespeed reley and wiring connector. That there is a fault code in gear which is P2908 clutch subsystem . the car is able to engage into 1st gear and reverse gear